Exactly How to Set up a Tub Yourself
Exactly How to Set up a Tub Yourself
Blog Article
The writer is making a number of good pointers regarding Installing A Bathtub overall in this great article underneath.
Mounting a bath tub isn't specifically brain surgery, yet it does call for strong plumbing, woodworking, as well as often, tiling skills. Changing an old bath tub with a brand-new one is likewise a reasonably challenging project. If the old tub is conveniently easily accessible, the project can relocate easily; if you have to open a wall surface to get rid of the old bathtub as well as position the new bathtub, the task is a lot harder. In either instance, the job is within a home handyman's skills, although you will certainly require an assistant to leave the old tub and embeded in the brand-new one. Make certain you have certified on your own for the task and are comfortable trying it. As opposed to hiring a contractor to take control of a halfway-completed job, it is better to consider using one prior to you begin. Chances are you might need a professional plumber to make tube links.
This post will certainly aid you set up a brand-new tub in your bathroom if you have actually already acquired a new bathtub and do not need to transform the setup of your previous water system pipes.
Your devices as well as material list ought to comprise the following:
Planning for the Installation
To start with, the supporting structure supplied with the bathroom must be fitted (if required) according to the maker's instructions. Next off, fit the taps or mixer to the tub. When fitting the faucet block, it is essential to make certain that if the tap includes a plastic washer, it is fitted in between the bath as well as the taps. On a plastic bath, it is likewise sensible to fit a sustaining plate under the taps unit to avoid strain on the bath tub.
Fit the versatile faucet ports to the bottom of the two faucets using 2 nuts and also olives (in some cases provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the outlet via the hole in the bath. Make use of the nut supplied by the supplier to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the versatile overflow pipe to the overflow electrical outlet. After that, screw the pipe to the overflow face which should be fitted inside the bath. See to it you utilize all of the provided washing machines.
Connect the catch to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Attach the bottom of the overflow tube in a similar manner.The bathroom must currently prepare to be suited its final setting.
Removing Old Taps
If you need to replace old taps with new ones as a part of your installation, then the first thing you should do is disconnect the water. After doing so, activate the faucets to drain pipes any water remaining in the system. The process of removing the existing taps can be quite problematic because of the restricted gain access to that is typically the situation.
Utilize a basin wrench (crowsfoot spanner) or a tap tool to undo the nut that links the supply pipes to the taps. Have a cloth ready for the remaining water that will come from the pipes. As soon as the supply pipelines have actually been gotten rid of, use the same tool to loosen the nut that holds the taps onto the bath/basin. You will certainly require to quit the solitary faucets from transforming throughout this process. When the taps have been gotten rid of, the holes in the bath/basin will certainly need to be cleaned up of any type of old sealing compound.
Before going on to fit the brand-new faucets, contrast the pipe connections on the old taps to the brand-new faucets. If the old faucets are longer than the new taps, then a shank adapter is needed for the brand-new faucets to fit.
Setting up the Bathtub
Using both wood boards under its feet, put the tub in the required position. The wood boards are practical in uniformly spreading out the weight of the bath tub over the area of the boards instead of focusing all the weight onto four tiny factors.
The next goal is to ensure that the bath tub is leveled all round. This can be accomplished by inspecting the spirit level and also changing the feet on the tub until the level checks out level.
To mount faucets, fit the bottom of the outermost adaptable tap connector to the ideal supply pipe by making a compression join; after that do the same for the various other faucet.
Turn on the supply of water and examine all joints and also new pipework for leakages and also tighten them if needed. Fill up the bathtub and additionally examine the overflow outlet and the regular electrical outlet for leaks.
Finally, deal with the bathroom paneling as described in the manufacturer's user's manual. Tiling as well as sealing around the bath tub must wait until the bath tub has actually been used at the very least once as this will resolve it into its last setting.
Fitting New Touches
If the tails of the new taps are plastic, after that you will require a plastic port to prevent damages to the thread. One end of the connector fits on the plastic tail of the faucet and the various other end offers a connection to the existing supply pipelines.
If you need to fit a monobloc, then you will certainly require decreasing couplers, which links the 10mm pipeline of the monobloc to the basic 15mm supply pipeline.
Next off, position the tap in the placing hole in the bath/basin guaranteeing that the washing machines remain in place between the faucet and also the sink. Secure the tap in position with the supplier provided backnut. When the faucet is safely in position, the supply pipelines can be attached to the tails of the taps. The faucets can either be attached by using corrugated copper piping or with typical faucet connectors. The former kind should be linked to the faucet ends first, tightening up just by hand. The supply pipes can later be attached to the various other end. Tighten both ends with a spanner after both ends have actually been attached.
Tiling Around the Bathtub
In the area where the bathroom fulfills the tile, it is required to secure the accompanies a silicone rubber caulking. This is important as the fitting can relocate sufficient to crack a rigid seal, triggering the water to pass through the wall surface between the bath as well as the tiling, leading to difficulties with wetness and also feasible leakages to the ceiling listed below.
You can choose from a variety of coloured sealers to assimilate your components and fittings. They are sold in tubes and cartridges, and are capable of sealing voids up to a size of 3mm (1/8 inch). If you have a bigger void to load, you can load it with spins of drenched paper or soft rope. Bear in mind to constantly fill up the tub with water before sealing, to enable the movement experienced when the tub is in use. The sealer can fracture rather very early if you do not think about this activity prior to sealing.
Additionally, ceramic coving or quadrant tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are likewise quickly available on the market. It is suggested to fit the ceramic tiles utilizing water-resistant or waterproof adhesive and also cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I recently found that blog posting about A Step-by-Step Guide to Installing a Bathtub when doing research the internet. Are you aware of somebody who is fascinated about the topic? Feel free to share it. Many thanks for going through it.
Schedule And Pricing
Report this page